Dodge Journey 2011 Owner'S Manual Download Page 451 | Manualshive

Page: 451 / 559

background image

Without The Ignition Key

Front-Wheel Drive (FWD)

Special care must be taken when the vehicle is towed
with the ignition in the LOCK/OFF position. Flatbed
towing is the preferred towing method. However, if a
flatbed towing vehicle is not available, wheel lift towing
equipment may be used. Rear towing (with the front
wheels on the ground) is not allowed, as transmission
damage will occur. If rear towing is the only alternative,
the front wheels must be placed on a towing dolly. Proper
towing equipment is necessary to prevent damage to the
vehicle.

All-Wheel Drive (AWD)

The manufacturer requires towing your vehicle with all
four wheels OFF the ground using a flatbed.

CAUTION!

Failure to follow these towing methods can cause
severe damage to the transmission and/or transfer
case. Such damage is not covered by the New Vehicle
Limited Warranty.

6

WHAT TO DO IN EMERGENCIES

449

«
...
449
450
451
452
453
...
»

Summary of Contents for Journey 2011
















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Journey 2011

Brand: iArmor Pages: 6

Brand: Axxess Pages: 8

Brand: Oypla Leisure Pages: 4

GMC Yukon Denali 2005

Brand: Cadillac Pages: 456

Brand: Saab Pages: 63

Brand: R&G Pages: 20

Brand: Whispbar Pages: 70

Brand: Kia Pages: 58

Brand: Lantronix Pages: 51

Brand: Renault Pages: 198

K40 Platinum360

Brand: K40 ELECTRONICS Pages: 11

84 61 0 028 926

Brand: BMW Pages: 13

Brand: Roadtrek Pages: 61

COOPER Convertible

Brand: Mini Pages: 168

Brand: BMW Pages: 242

Brand: ULTIMATE SPEED Pages: 18

Brand: Toyota Pages: 923

Brand: Metra Electronics Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands