Dodge Journey 2011 Owner'S Manual Download Page 263 | Manualshive

Page: 263 / 559

background image

•

Each time the ignition is turned to ON/RUN, the ESC
system will be ON, even if it was turned off previously.

•

The ESC system will make buzzing or clicking sounds
when it is active. This is normal; the sounds will stop
when ESC becomes inactive following the maneuver
that caused the ESC activation.

5. Turn Signal Indicators

The arrow will flash with the exterior turn signal
when the turn signal lever is operated.

If the vehicle electronics sense that the vehicle is driven
more than 1 mile (1.6 km) with either turn signal on, a
continuous chime will sound to alert you to turn the
signals off. If either indicator flashes at a rapid rate, check
for a defective outside light bulb.

6. High Beam Indicator

This indicator shows that the high beam head-
lights are on. Push the multifunction lever forward

to switch the headlights to high beam, and pull toward
yourself (normal position) to return to low beam.

7. Front Fog Light Indicator — If Equipped

This indicator will illuminate when the front fog
lights are on.

8. Electronic Vehicle Information Center (EVIC)
Display

Odometer

The odometer display shows the total distance the ve-
hicle has been driven.

U.S. Federal regulations require that upon transfer of
vehicle ownership, the seller certify to the purchaser the
correct mileage that the vehicle has been driven. If your
odometer needs to be repaired or serviced, the repair

4

UNDERSTANDING YOUR INSTRUMENT PANEL

261

«
...
261
262
263
264
265
...
»

Summary of Contents for Journey 2011
















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Journey 2011

Brand: JAC Pages: 70

Brand: Jabra Pages: 10

SP200 - QUICKSTART GUIDE 1

Brand: Jabra Pages: 2

BT150 - Headset - Over-the-ear

Brand: Jabra Pages: 2

Brand: RAM Pages: 292

Brand: RAM Pages: 116

Chevrolet Silverado 2500HD 2021

Brand: GMC Pages: 433

Brand: hc-cargo Pages: 60

Brand: Whelen Engineering Company Pages: 9

Brand: Volvo Pages: 18

Brand: FIRRAK Pages: 12

Brand: BabySafe Pages: 43

Brand: E-Lead Pages: 11

Brand: Vauxhall Pages: 4

BLADE-AL-HK4-EN

Brand: iDataLink Pages: 35

Brand: MovaNext Pages: 4

Brand: Ranger design Pages: 6

Brand: Wallbox Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands