Dodge Journey 2011 Owner'S Manual Download Page 438 | Manualshive

Page: 438 / 559

background image

WARNING!

Raising the vehicle higher than necessary can make
the vehicle less stable. It could slip off the jack and
hurt someone near it. Raise the vehicle only enough
to remove the tire.

5. Remove the wheel nuts. For vehicles so equipped,
remove the wheel cover from the wheel by hand. Do not
pry the wheel cover off. Then pull the wheel off the hub.

WARNING!

To avoid possible personal injury, handle the wheel
covers with care to avoid contact with any sharp
edges.

NOTE:

For vehicles so equipped, the wheel cover is

held on the wheel by the wheel nuts. When reinstalling
the original wheel, properly align the wheel cover to the
valve stem, place the wheel cover onto the wheel, and
then install the wheel nuts.

6. Install the spare tire.

NOTE:

•

For vehicles so equipped, do not attempt to install a
center cap or wheel cover on the compact spare. Do
not use a hammer or force to install the wheel covers.

•

Refer to “Compact Spare Tire” and to “Limited-Use
Spare” under “Tires — General Information” in “Start-
ing and Operating” for additional warnings, cautions,
and information about the spare tire, its use, and
operation.

7. Install the wheel nuts with the cone-shaped end of the
nut toward the wheel. Lightly tighten the wheel nuts.

436

WHAT TO DO IN EMERGENCIES

«
...
436
437
438
439
440
...
»

Summary of Contents for Journey 2011
















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Journey 2011

Brand: Camcar Pages: 6

MagicWatch MWE800

Brand: Waeco Pages: 212

OCTAVIA - TECHNICAL CHANGES 11-2009

Brand: Skoda Pages: 16

Brand: Thule Pages: 12

Crossland X 2017

Brand: Vauxhall Pages: 245

Brand: Subaru Pages: 44

CMPC-22 Fujitsu-Siemens PocketLoox 410

Brand: Carcomm Pages: 2

Brand: Meritor Pages: 20

SB-J-GCHER2/10W3v2

Brand: Stealthbox Pages: 2

Airgo Active cushion / Comfort

Brand: TOGU Pages: 2

Brand: Westin Pages: 3

Brand: Truma Pages: 16

Brand: WABCO Pages: 40

Brand: TigerTough Pages: 7

Brand: Alu-Cab Pages: 6

Brand: GMC Pages: 312

ActiveStart ACS30P

Brand: Active Controls Pages: 2

2001 MR2 Spyder

Brand: Toyota Pages: 234

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands