Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 78 | Manualshive

Page: 78 / 427

background image

remain in a forward-facing child seat with a harness for
as long as possible, up to the highest weight or height
allowed by the child seat.

All children whose weight or height is above the
forward-facing limit for the child seat should use a
belt-positioning booster seat until the vehicle’s seat belts
fit properly. If the child cannot sit with knees bent over
the vehicle’s seat cushion while the child’s back is against
the seatback, they should use a belt-positioning booster
seat. The child and belt-positioning booster seat are held
in the vehicle by the seat belt.

WARNING!

•

Improper installation can lead to failure of an
infant or child restraint. It could come loose in a
collision. The child could be badly injured or
killed. Follow the child restraint manufacturer’s

(Continued)

WARNING!

(Continued)

directions exactly when installing an infant or
child restraint.

•

After a child restraint is installed in the vehicle, do
not move the vehicle seat forward or rearward
because it can loosen the child restraint attach-
ments. Remove the child restraint before adjusting
the vehicle seat position. When the vehicle seat has
been adjusted, reinstall the child restraint.

•

When your child restraint is not in use, secure it in
the vehicle with the seat belt or LATCH anchor-
ages, or remove it from the vehicle. Do not leave it
loose in the vehicle. In a sudden stop or accident, it
could strike the occupants or seatbacks and cause
serious personal injury.

76

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
76
77
78
79
80
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: IAG Pages: 3

Brand: Ironton Pages: 7

Brand: Pyle Pages: 4

Automotive 31006

Brand: KRAFTWERK Pages: 2

Wireless Handsfree Car Kit

Brand: Wagan Pages: 20

Brand: EZTRUNK Pages: 3

Brand: Gatorback Mudflaps Pages: 4

Brand: Quadratec Pages: 12

Brand: Gator Pages: 8

Brand: benbat Pages: 14

Brand: SPL Pages: 5

Brand: Connects2 Pages: 8

2005-2009 Chrysler 300C

Brand: Mopar Pages: 7

CHALLENGER HELLCAT 2017

Brand: Dodge Pages: 484

Sebring Convertible

Brand: Chrysler Pages: 454

Brand: Kargo Master Pages: 17

Brand: Whispbar Pages: 43

Brand: Nav TV Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands