Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 25 | Manualshive

Page: 25 / 427

background image

Using The Panic Alarm

To turn the Panic Alarm feature on or off, push and hold
the PANIC

button on the RKE transmitter for at

least one second and release. When the Panic Alarm is
on, the headlights will turn on, the park lights will
flash, the horn will pulse on and off, and the interior
lights will turn on.

The Panic Alarm will stay on for three minutes unless
you turn it off by either pushing the PANIC

button a

second time or drive the vehicle at a speed of 15 MPH
(24 km/h) or greater.

NOTE:

The interior lights will turn off if you cycle the

ignition switch to the ACC or ON/RUN position while
the Panic Alarm is activated. However, the exterior lights
and horn will remain on.

Programming Additional Transmitters

Programming Key Fobs or RKE transmitters may be
performed at an authorized dealer.

Transmitter Battery Replacement

The recommended replacement battery is one CR2032
battery.

NOTE:

•

Perchlorate Material — special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate

•

Do not touch the battery terminals that are on the back
housing or the printed circuit board.

1. Remove the emergency key by sliding the mechanical

latch on the back of the RKE transmitter sideways
with your thumb and then pull the key out with your
other hand.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

23

«
...
23
24
25
26
27
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: Jeep Pages: 25

Brand: Jeep Pages: 51

Brand: Farenheit Pages: 8

Brand: Yakima Pages: 4

Brand: Paxton Automotive Pages: 85

Brand: Thule Pages: 8

2008 MX-5 Miata

Brand: Mazda Pages: 400

Car Cup Holder Phone Mount

Brand: UGREEN Pages: 9

Code Alarm PROFESSIONAL SERIES CA 5550SST

Brand: Audiovox Pages: 14

Brand: Fab Fours Pages: 19

Brand: E&G Classics Pages: 2

Parktronic system Volkswagen Golf MK7

Brand: Car-Systems Pages: 10

Brand: Sagem Pages: 10

Brand: Veldo Teknoloji Pages: 32

Brand: v.link Pages: 19

Brand: Prorack Pages: 15

Brand: Huf Pages: 6

Brand: Lincoln Pages: 586

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands