Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 180

Page: 180 / 427

DID Selectable Menu Items

Push and release the

DOWN

arrow buttons until

the desired Selectable Menu icon is highlighted in the
DID.

Tachometer

Push and release the

DOWN

arrow

button until the Tachometer icon is highlighted
in the DID. Push and release the

RIGHT

arrow

button to change the display between full

tachometer or tachometer with digital speedometer.

MPH To km/h

Push and release the

DOWN

arrow

button until the MPH to km/h icon is high-
lighted in the DID. Push and release the

button to change the display between MPH

or km/h.

Vehicle Info (Customer Information Features)

Push and release the

DOWN

arrow

button until the Vehicle Info icon is highlighted
in the DID. Push and release the

RIGHT

arrow

button to display the following information

submenus:

178

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Search results

Summary of Contents for 2016 Viper SRT ACR

Reviews:

Related manuals for 2016 Viper SRT ACR

Brands by name

Popular brands

Dodge 2016 Viper SRT ACR, Owner'S Manual

Search results

Summary of Contents for 2016 Viper SRT ACR

Reviews:

Related manuals for 2016 Viper SRT ACR

Brands by name

Popular brands