Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 195 | Manualshive

Page: 195 / 427

background image

designated turn within a programmed route. To turn on
or enable, press the Navigation Turn-By-Turn In Cluster
button on the touchscreen, until a check-mark appears
next to the setting, showing that setting has been se-
lected. Press the back arrow button on the touchscreen to
return to the previous menu or push the back button on
the faceplate.

Voice

After pressing the “Voice” button on the touchscreen the
following settings will be available:

•

Voice Response Length

When in this display, you may change the Voice Re-
sponse Length settings. To change the Voice Response
Length, press the “Brief” or “Detailed” button on the
touchscreen until a check-mark appears next to the
setting, showing that setting has been selected.

•

Show Command List

When in this display, you may choose to Always, With
Help, or Never display the Teleprompter with possible
options while in a voice session. To change the Show
Command List settings, press the “Always,” “With
Help,” or “Never” button on the touchscreen until a
check-mark appears next to the setting, showing that
setting has been selected.

Clock

After pressing the “Clock” button on the touchscreen the
following settings will be available:

•

Sync Time With GPS

This feature will allow you to automatically have the
radio set the time. To change the Sync Time setting, press
the “Sync with GPS Time” button on the touchscreen
until a check-mark appears next to the setting, showing
that setting has been selected. Press the back arrow

4

UNDERSTANDING YOUR INSTRUMENT PANEL

193

«
...
193
194
195
196
197
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: IAG Pages: 3

Brand: Mazdaspeed Pages: 8

Brand: Ford Pages: 38

Brand: Honda Pages: 4

SAFESTOP SS0005

Brand: Pro-gard Pages: 4

1506-PHX Cargo Plus

Brand: Ranger design Pages: 8

Brand: AUTOTECH Pages: 1

Brand: Yakima Pages: 13

Brand: Draw tite Pages: 4

Brand: EFILive Pages: 25

Brand: Power Acoustik Pages: 4

Brand: Skoda Pages: 324

Brand: Streetwize Pages: 4

Brand: Toyota Pages: 497

MagicSafe MSG150

Brand: Waeco Pages: 20

Brand: Volvo Pages: 18

C-Max Energi 2014

Brand: Ford Pages: 10

Brand: Blue Ox Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands