Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 321 | Manualshive

Page: 321 / 427

background image

WARNING!

To avoid the risk of forcing the vehicle off the jack,
do not tighten the lug nuts fully until the vehicle has
been lowered. Failure to follow this warning may
result in personal injury.

TIRE SERVICE KIT — IF EQUIPPED

Small punctures up to 1/4 inch (6 mm) in the tire tread
can be sealed with Tire Service Kit. Foreign objects
(e.g., screws or nails) should not be removed from the
tire. Tire Service Kit can be used in outside temperatures
down to approximately -4°F (-20°C).

This kit will provide a temporary tire seal, allowing you
to drive your vehicle up to 100 miles (160 km) with a
maximum speed of 55 mph (90 km/h).

Tire Service Kit Storage

The Tire Service Kit is located in the left side of the trunk.

Tire Service Kit Location

6

WHAT TO DO IN EMERGENCIES

319

«
...
319
320
321
322
323
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: Kargo Master Pages: 6

Brand: JETBAG Pages: 44

Brand: Cequent Pages: 9

Brand: Metra Electronics Pages: 8

Brand: Thule Pages: 8

Brand: TOP VEHICLE TECH Pages: 8

Brand: Lexus Pages: 6

Brand: CITROEN Pages: 86

Brand: Mazda Pages: 605

Automobille 2004 Century

Brand: Buick Pages: 12

Brand: Blue Ox Pages: 8

Brand: Buzz Rack Pages: 8

CAB HIGH SPORT BED CAP

Brand: Leer Pages: 32

Brand: Toyota Pages: 31

Actyon Sports 2006

Brand: SSANGYONG Pages: 90

PRIUS PRIME 2018

Brand: Toyota Pages: 68

Brand: Blueant Pages: 73

Brand: Blueant Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands