Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 229

Page: 229 / 427

Apple iPhone iOS 6 or later supports reading

incoming

text messages only. To enable this feature on your Apple
iPhone, follow these 4 simple steps:

TIP:

Voice Text Reply is not compatible with iPhone, but

if your vehicle is equipped with Siri Eyes Free, you can
use your voice to send a text message.

iPhone Notification Settings

1 — Select “Settings”
2 — Select “Bluetooth”
3 — Select the (i) for the paired vehicle
4 — Turn on “Show Notifications”

UNDERSTANDING YOUR INSTRUMENT PANEL

227

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Search results

Summary of Contents for 2016 Viper SRT ACR

Reviews:

Related manuals for 2016 Viper SRT ACR

Brands by name

Popular brands

Dodge 2016 Viper SRT ACR, Owner'S Manual

Search results

Summary of Contents for 2016 Viper SRT ACR

Reviews:

Related manuals for 2016 Viper SRT ACR

Brands by name

Popular brands