Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 349 | Manualshive

Page: 349 / 427

background image

WARNING!

•

Battery fluid is a corrosive acid solution and can
burn or even blind you. Do not allow battery fluid
to contact your eyes, skin, or clothing. Do not lean
over a battery when attaching clamps. If acid
splashes in eyes or on skin, flush the area imme-
diately with large amounts of water.

•

Battery gas is flammable and explosive. Keep
flame or sparks away from the battery. Do not use
a booster battery or any other booster source with
an output greater than 12 Volts. Do not allow cable
clamps to touch each other.

•

Battery posts, terminals, and related accessories
contain lead and lead compounds. Wash hands
after handling.

CAUTION!

•

It is essential when replacing the cables on the
battery that the positive cable is attached to the
positive post and the negative cable is attached to
the negative post. Battery posts are marked positive
(+) and negative (-) and are identified on the
battery case. Cable clamps should be tight on the
terminal posts and free of corrosion.

•

If a “fast charger” is used while the battery is in the
vehicle, disconnect both vehicle battery cables be-
fore connecting the charger to the battery. Do not
use a “fast charger” to provide starting voltage.

Hibernation Mode

The Hibernation mode feature conserves battery power
when storing the vehicle. It allows for up to three months

7

MAINTAINING YOUR VEHICLE

347

«
...
347
348
349
350
351
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: Ecco Pages: 9

Brand: Ecco Pages: 9

Brand: TATA Motors Pages: 164

Brand: iDataLink Pages: 30

MagicWatch MWE800

Brand: Waeco Pages: 212

Brand: Allen Sports Pages: 2

Brand: Subaru Pages: 99

2004 Vibe Navigation System

Brand: Pontiac Pages: 44

Brand: BURY Pages: 2

Brand: SuperATV Pages: 7

Brand: Pyle Pages: 2

Brand: Mobileye Pages: 29

Brand: Ford Pages: 4378

Brand: Toyota Pages: 549

Brand: Subaru Pages: 16

Brand: Gator Pages: 18

Brand: Ford Pages: 292

Brand: Road Ranger Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands