Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 295 | Manualshive

Page: 295 / 427

background image

These indicators are molded into the bottom of the tread
grooves. They will appear as bands when the tread depth
becomes a 1/16 of an inch (1.6 mm). When the tread is

worn to the tread wear indicators, the tire should be
replaced. Refer to “Replacement Tires” in this section for
further information.

Life Of Tire

The service life of a tire is dependent upon varying
factors including, but not limited to:

•

Driving style.

•

Tire pressure - Improper cold tire inflation pressures
can cause uneven wear patterns to develop across the
tire tread. These abnormal wear patterns will reduce
tread life, resulting in the need for earlier tire replace-
ment.

•

Distance driven.

•

Performance tires, tires with a speed rating of V or
higher, and Summer tires typically have a reduced

Tire Tread

1 — Worn Tire
2 — New Tire

5

STARTING AND OPERATING

293

«
...
293
294
295
296
297
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Titanium Series

Brand: Fass Pages: 13

Prestige APS-45B

Brand: Audiovox Pages: 8

Brand: Volvo Pages: 138

Brand: Whispbar Pages: 85

Brand: Harbor Freight Tools Pages: 12

Brand: Honda Pages: 3

BTFREQ PRO BTFMPD3SR

Brand: Scosche Pages: 16

Brand: Yakima Pages: 13

Brand: Draw tite Pages: 4

Brand: Lantronix Pages: 51

Brand: v.link Pages: 19

Brand: CITROEN Pages: 394

Brand: Gator Pages: 5

Brand: Saab Pages: 498

Brand: Prorack Pages: 15

VIEWLINE TEMPERATURE GAUGES

Brand: VDO Pages: 5

Brand: Bestop Pages: 14

Brand: Kuda-Phonebase Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands