Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 228

Page: 228 / 427

Voice Text Reply

Uconnect will announce

incoming

text messages. Push

the Phone button

and say

Listen.

(Must have com-

patible mobile phone paired to Uconnect system.)

1. Once an incoming text message is read to you, push

the Phone button

. After the beep, say:

“Reply.”

2. Listen to the Uconnect prompts. After the beep, repeat

one of the pre-defined messages and follow the system
prompts.

PRE-DEFINED VOICE TEXT REPLY RESPONSES

Yes.

Stuck in traffic.

See you later.

No.

Start without

me.

I’ll be late.

Okay.

Where are you?

I will be

minutes late.

Call me.

Are you there

yet?

I’ll call you

later.

I need

directions.

See you in

<number> of

minutes.

I’m on my way.

Can’t talk right

now.

I’m lost.

Thanks.

TIP:

Your mobile phone must have the full implemen-

tation of the

Message Access Profile (MAP)

to take

advantage of this feature. For details about MAP, visit
UconnectPhone.com.

226

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Search results

Summary of Contents for 2016 Viper SRT ACR

Reviews:

Related manuals for 2016 Viper SRT ACR

Brands by name

Popular brands

Dodge 2016 Viper SRT ACR, Owner'S Manual

Search results

Summary of Contents for 2016 Viper SRT ACR

Reviews:

Related manuals for 2016 Viper SRT ACR

Brands by name

Popular brands