Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 182

Page: 182 / 427

Engine Hours

Push and release the

DOWN

arrow button until

“Engine Hours” is highlighted in the DID. Push and
release the

RIGHT

arrow button, and the engine hours

will be displayed.

Intake Air Temp.

Push and release the

DOWN

arrow button until

“Intake Air Temp.” is highlighted in the DID. Push and
release the

RIGHT

arrow button, and the intake air

temperature will be displayed.

Current Torque

Push and release the

DOWN

arrow button until

“Current Torque” is highlighted in the DID. Push and
release the

RIGHT

arrow button, and the current torque

will be displayed.

Current Power

Push and release the

DOWN

arrow button until

“Current Power” is highlighted in the DID. Push and
release the

RIGHT

arrow button, and the current power

will be displayed.

Fuel Economy

Push and release the

DOWN

arrow

button until the Fuel Economy icon is high-
lighted and the following will display:

Range To Empty (RTE)

Average Fuel Economy/Miles Per Gallon (MPG Bar-
graph)

Current Miles Per Gallon (MPG)

180

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Search results

Summary of Contents for 2016 Viper SRT ACR

Reviews:

Related manuals for 2016 Viper SRT ACR

Brands by name

Popular brands

Dodge 2016 Viper SRT ACR, Owner'S Manual

Search results

Summary of Contents for 2016 Viper SRT ACR

Reviews:

Related manuals for 2016 Viper SRT ACR

Brands by name

Popular brands