Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 426 | Manualshive

Page: 426 / 427

background image

INSTALLATION OF RADIO TRANSMITTING
EQUIPMENT

Special design considerations are incorporated into this
vehicle’s electronic system to provide immunity to radio
frequency signals. Mobile two-way radios and telephone
equipment must be installed properly by trained person-
nel. The following must be observed during installation.

The positive power connection should be made directly
to the battery and fused as close to the battery as possible.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection.
This connection should not be fused.

Antennas for two-way radios should be mounted on the
roof or the rear area of the vehicle. Care should be used
in mounting antennas with magnet bases. Magnets may
affect the accuracy or operation of the compass on
vehicles so equipped.

The antenna cable should be as short as practical and
routed away from the vehicle wiring when possible. Use
only fully shielded coaxial cable.

Carefully match the antenna and cable to the radio to
ensure a low Standing Wave Ratio (SWR).

Mobile radio equipment with output power greater than
normal may require special precautions.

All installations should be checked for possible interfer-
ence between the communications equipment and the
vehicle’s electronic systems.

«
...
424
425
426
427
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: LAS Pages: 44

Brand: LAS Pages: 24

Brand: Kia Pages: 385

ANDROID INTERFACE

Brand: GMC Pages: 18

Brand: Prorack Pages: 15

Brand: METRON Pages: 4

Brand: Ecco Pages: 9

Brand: Vauxhall Pages: 95

Brand: Roadmaster Pages: 4

2008 Savana Van

Brand: GMC Pages: 402

Sprinter Bed System DIY

Brand: FVC Pages: 8

PRO-FLO XT 3527

Brand: Edelbrock Pages: 39

Brand: Kargo Master Pages: 9

Brand: NavLinkz Pages: 26

Brand: Menabo Pages: 12

2014 All vehicles

Brand: Jeep Pages: 44

Brand: Prorack Pages: 13

Brand: Kia Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands