Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 155 | Manualshive

Page: 155 / 427

background image

The light will remain on until the cause is corrected.

NOTE:

The light may flash momentarily during sharp

cornering maneuvers, which change fluid level condi-
tions. The vehicle should have service performed, and
the brake fluid level checked.

If brake failure is indicated, immediate repair is neces-
sary.

WARNING!

Driving a vehicle with the red brake light on is
dangerous. Part of the brake system may have failed.
It will take longer to stop the vehicle. You could have
a collision. Have the vehicle checked immediately.

Vehicles equipped with the Anti-Lock Brake System
(ABS) are also equipped with Electronic Brake Force
Distribution (EBD). In the event of an EBD failure, the

Brake Warning Light will turn on along with the ABS
Light. Immediate repair to the ABS system is required.

Operation of the Brake Warning Light can be checked by
turning the ignition switch from the OFF position to the
ON/RUN position. The light should illuminate for ap-
proximately two seconds. The light should then turn off
unless the parking brake is applied or a brake fault is
detected. If the light does not illuminate, have the light
inspected by an authorized dealer.

The light also will turn on when the parking brake is
applied with the ignition switch in the ON/RUN posi-
tion.

NOTE:

This light shows only that the parking brake is

applied. It does not show the degree of brake application.

4

UNDERSTANDING YOUR INSTRUMENT PANEL

153

«
...
153
154
155
156
157
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: Ironton Pages: 7

Brand: Saab Pages: 3

v.LOGiC Intelligent Solution V5-NTG46

Brand: Caraudio-Systems Pages: 18

Brand: MULTILIFT Pages: 62

Brand: Cadillac Pages: 352

Brand: Xpresskit Pages: 18

Brand: Thule Pages: 3

Prime Design VBI-FT31B

Brand: Safe Fleet Pages: 12

Brand: Acura Pages: 7

Brand: Bilstein Pages: 7

Brand: Brodit Pages: 2

Brand: Ace K9 Pages: 14

Brand: Buick Pages: 475

Brand: Technaxx Pages: 59

Brand: Chevrolet Pages: 324

Brand: GAC MOTOR Pages: 356

Brand: Westfalia Pages: 97

Brand: Honda Pages: 286

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands