Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 83 | Manualshive

Page: 83 / 427

background image

Installing Child Restraints Using The Top Tether
Anchorage

WARNING!

Do not attach a tether strap for a rear-facing car seat
to any location in front of the car seat, including the
seat frame or a tether anchorage. Only attach the
tether strap of a rear-facing car seat to the tether
anchorage that is approved for that seating position,
located behind the top of the vehicle seat. See the
section “Lower Anchors and Tethers for CHildren
(LATCH) Restraint System” for the location of ap-
proved tether anchorages in your vehicle.

There is a tether strap anchor located behind
the child tether access cover behind the passen-
ger seat. To attach a child restraint tether strap
to the anchor:

1. Move the seat forward.

2. Move the seatback to its full forward position.

3. Remove the child tether access cover by prying either

side with a screwdriver or similar tool, as shown.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

81

«
...
81
82
83
84
85
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: Kargo Master Pages: 6

Brand: VEAP SHIELD UNITED Pages: 3

Brand: GOgroove Pages: 9

Brand: CITROEN Pages: 52

Brand: Mazda Pages: 13

Brand: hc-cargo Pages: 60

Brand: Alfa Romeo Pages: 8

BASIC TLL171231

Brand: Tellur Pages: 5

Brand: Unex Pages: 30

Brand: Mercedes-Benz Pages: 91

PRIME DESIGN HRR-369-E-UM3-96

Brand: Safe Fleet Pages: 12

Brand: Kocchi's Pages: 4

Brand: EUFAB Pages: 4

Brand: PEUGEOT Pages: 232

Telescoping Computer Base C-TCB-34

Brand: Havis-Shields Pages: 1

Brand: PEUGEOT Pages: 107

Brand: Webasto Pages: 44

Brand: Ranger design Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands