Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 112 | Manualshive

Page: 112 / 427

background image

Turn Signals

Move the multifunction lever up or down and the arrows
on each side of the instrument cluster flash to show
proper operation of the front and rear turn signal lights.

NOTE:

•

If either light remains on and does not flash, or there is
a very fast flash rate, check for a defective outside light
bulb. If an indicator fails to light when the lever is
moved, it would suggest that the indicator bulb is
defective.

•

A “Turn Signal On” message will appear in the Driver
Information Display (DID) and a continuous chime
will sound if the vehicle is driven more than 1 mile
(1.6 km) with either turn signal on.

High/Low Beam Switch

Push the multifunction lever away from you to switch
the headlights to high beam. Pull the multifunction lever
toward you to switch the headlights back to low beam.

Flash-To-Pass

You can signal another vehicle with your headlights by
lightly pulling the multifunction lever toward you. This
will turn on the high beams headlights until the lever is
released.

110

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
110
111
112
113
114
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

MARTEN-FREE CAR

Brand: Gardigo Pages: 36

X-ACT CONTOUR 53491

Brand: HUSKY LINERS Pages: 2

Brand: Volvo Pages: 19

Brand: GMC Pages: 425

Brand: Chevrolet Pages: 344

Brand: Prorack Pages: 15

Brand: Aries Pages: 5

Brand: Mercedes-Benz Pages: 354

Brand: Calix group Pages: 4

Brand: MAcarbon Pages: 3

Brand: Xingyun Pages: 74

Brand: Acura Pages: 347

Brand: Blaupunkt Pages: 6

Outlander Plug-in hybrid

Brand: Mitsubishi Pages: 28

Brand: Chevrolet Pages: 46

Brand: Porsche Pages: 145

Brand: Curt Manufacturing Pages: 4

Brand: Fiat Pages: 220

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands