Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 137 | Manualshive

Page: 137 / 427

background image

NOTE:

Do not exceed the maximum power of 160 Watts

(13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power
rating is exceeded the fuse protecting the system will
need to be replaced.

WARNING!

To avoid serious injury or death:

•

Only devices designed for use in this type of outlet
should be inserted into any 12 Volt outlet.

•

Do not touch with wet hands.

•

Close the lid when not in use and while driving the
vehicle.

•

If this outlet is mishandled, it may cause an electric
shock and failure.

CAUTION!

•

Many accessories that can be plugged in draw
power from the vehicle’s battery, even when not
in use (i.e., cellular phones, etc.). Eventually, if
plugged in long enough, the vehicle’s battery will
discharge sufficiently to degrade battery life and/or
prevent the engine from starting.

(Continued)

Center Console Outlet

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

135

«
...
135
136
137
138
139
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: PAC Pages: 15

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 2

Brand: Cadillac Pages: 494

Brand: Cadillac Pages: 500

Brand: Cadillac Pages: 40

Brand: Cadillac Pages: 432

Brand: Cadillac Pages: 338

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 438

Brand: Axxess Pages: 8

Brand: SeaSucker Pages: 9

Brand: Safe Fleet Pages: 38

Brand: Whispbar Pages: 15

Brand: Pyle Pages: 4

Green Motion DC 66

Brand: Eaton Pages: 18

Brand: Metra Electronics Pages: 20

DLD Wide Range II

Brand: VDO Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands