Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 223

Page: 223 / 427

3. Speak clearly at a normal pace and volume while

facing straight ahead. The microphone is positioned
on the rearview mirror and aimed at the driver.

4. Each time you give a Voice Command, you must first

push either the VR or Phone button, wait until

after

the beep, then say your Voice Command.

5. You can interrupt the help message or system prompts

by pushing the VR or Phone button and saying a Voice
Command from current category.

Two buttons are all you need to control your Uconnect
system with your voice.

Voice Recognition (VR)/Phone Buttons

1 — Push To Begin Radio, Media, Navigation, Apps And Climate
Functions
2 — Push To Initiate Or To Answer A Phone Call, Send Or Re-
ceive A Text

UNDERSTANDING YOUR INSTRUMENT PANEL

221

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Search results

Summary of Contents for 2016 Viper SRT ACR

Reviews:

Related manuals for 2016 Viper SRT ACR

Brands by name

Popular brands

Dodge 2016 Viper SRT ACR, Owner'S Manual

Search results

Summary of Contents for 2016 Viper SRT ACR

Reviews:

Related manuals for 2016 Viper SRT ACR

Brands by name

Popular brands