Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 292 | Manualshive

Page: 292 / 427

background image

CAUTION!

Because of the reduced ground clearance, do not take
your vehicle through an automatic car wash with a
compact or limited-use temporary spare installed.
Damage to the vehicle may result.

Spare Tire Matching Original Equipped Tire And
Wheel — If Equipped

Your vehicle may be equipped with a spare tire and
wheel equivalent in look and function to the original
equipment tire and wheel found on the front or rear axle
of your vehicle. This spare tire may be used in the tire
rotation for your vehicle. If your vehicle has this option,
refer to an authorized tire dealer for the recommended
tire rotation pattern.

Compact Spare Tire — If Equipped

The compact spare is for temporary emergency use only.
You can identify if your vehicle is equipped with a
compact spare by looking at the spare tire description on
the Tire and Loading Information Placard located on the
driver’s side door opening or on the sidewall of the tire.
Compact spare tire descriptions begin with the letter “T”
or “S” preceding the size designation. Example: T145/
80D18 103M.

T, S = Temporary Spare Tire

Since this tire has limited tread life, the original equip-
ment tire should be repaired (or replaced) and reinstalled
on your vehicle at the first opportunity.

Do not install a wheel cover or attempt to mount a
conventional tire on the compact spare wheel, since the
wheel is designed specifically for the compact spare tire.

290

STARTING AND OPERATING

«
...
290
291
292
293
294
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: Jabra Pages: 10

Brand: Kathrein Pages: 7

Brand: Kolpin Outdoors Pages: 6

Brand: Schartec Pages: 2

Brand: Ford Pages: 38

Brand: U & Me Brothers Pages: 6

Brand: Acura Pages: 2

Brand: Cadillac Pages: 368

Brand: Luverne Pages: 3

Brand: Navman Pages: 27

Brand: Subaru Pages: 540

Brand: rough country Pages: 4

Brand: Volvo Pages: 197

TOUR EASY 4 936550

Brand: Reimo Pages: 4

Brand: Cadillac Pages: 339

Brand: Cadillac Pages: 538

Brand: Kuda-Phonebase Pages: 3

Brand: Federal Signal Corporation Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands