Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 169 | Manualshive

Page: 169 / 427

background image

Low Fuel Indicator Light

Yellow Telltale

Light

What It Means

Low Fuel Indicator Light

When the fuel level reaches approximately 1.5 gal (5.8 L) this light will turn on, and remain
on until fuel is added.

Anti-Lock Brake (ABS) Indicator Light

Yellow Telltale

Light

What It Means

Anti-Lock Brake (ABS) Indicator Light

After the ignition is turned on, the Anti-Lock Brake System (ABS) light illuminates to indi-
cate function check at vehicle startup. If the light remains on after startup or comes on and
stays on at road speeds, it may indicate that the ABS has detected a malfunction or has be-
come inoperative. The system reverts to standard non-anti-lock brakes.

4

UNDERSTANDING YOUR INSTRUMENT PANEL

167

«
...
167
168
169
170
171
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: UMBRA RIMORCHI Pages: 18

Brand: U & Me Brothers Pages: 6

Brand: STO N SHO Pages: 7

Brand: Motoalliance Pages: 5

Brand: Edelbrock Pages: 1

Brand: SSV Works Pages: 2

Brand: Poison Spyder Pages: 5

Brand: Chevrolet Pages: 324

Brand: ROLEC Pages: 2

Aura Mobile BT MCP-2014

Brand: Spracht Pages: 2

Brand: Chevrolet Pages: 55

Brand: Gold Lantern Pages: 1

Brand: Metec Pages: 2

Brand: iDataLink Pages: 11

Brand: OEM Audio Pages: 21

Brand: Saab Pages: 9

Brand: Kia Pages: 38

Brand: Metra Electronics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands