Docomo SH-05A, Instruction Manual

Page: 276 / 556

274
e13_dr20_7e.fm
[274/280]
i-
a
pp
li/
i-W
id
g
et
If i-
a
ppli To (Run i-
a
ppli) is set, i-
a
ppli can be started from a site,
i-mode mail, Message R/F, screen memo or ToruCa.
i- a ppli can also be started when the i- a ppli start signal is received in the
following methods.
Ir communication
When the
b
mark is held up to a scanning device
Bar code reader
Set whether to allow i-
a
ppli To in i-
a
ppli To settings (
n
P. 260).
Cannot be activated as i-
a
ppli stand-by.
Cannot be activated with Full Browser.
1
While viewing a site, mail, Message R/F, screen memo
or ToruCa, select i-
a
ppli
/ t /
[Yes].
:
To cancel: Press
H
while [i-
a
ppli activating] appears
/
[Yes].
Press
c
to operate i-
a
ppli set as the stand-by display. The i-
a
ppli
stand-by settings are not disabled, and the i-
a
ppli stand-by is restarted
when the stand-by display reappears.
Set whether to transmit from the software set as the i-
a
ppli stand-by,
using Stand-by network set (
n
P. 258).
1
In the Custom menu, select [Settings]
/
[Disp/LED/
Power saver]
/
[Set screen]
/
[Stand-by display]
/
[i-
a
ppli].
2
Select software
/ t
.
:
When the software using a transmission is set, a screen asking
whether to allow a transmission appears. Select [Yes] to allow a
transmission. When [No] is selected, data is not allowed to transmit
and information may not be sent.
:
To set a different i-
a
ppli as stand-by: Select [Settings]
/
select
software
/ t /
[Yes].
:
To end the i-
a
ppli set as stand-by: Select [End].
:
To disable the i-
a
ppli set as stand-by: Select [Cancel].
i-
a
ppli To
Running i-
a
ppli from sites or i-mode
mail
Starting i-
a
ppli from sites or i-mode mail
<i-
a
ppli To>
When i-
a
ppli is ended, the original site, received mail details screen,
screen memo or ToruCa display screen reappears.
If there is no software corresponding to the Run i-
a
ppli setting, [No
requested software] appears.
Depending on the site, the specified software can be downloaded or
updated if it is not saved on the FOMA terminal or if a newer version is
available for the software saved on the FOMA terminal.
Network set (
n
P. 260) may be required while i-
a
ppli software is
running.
i-
a
ppli To from i-mode mail is a function only available from i-mode mail
delivered from an IP (Information Provider). Not available for i-mode
mail exchanged between FOMA terminals.
i-
a
ppli stand-by
Setting i-
a
ppli as stand-by display
Only one software can be set as i-
a
ppli stand-by.
Some software cannot be set as i-
a
ppli stand-by.
If i-
a
ppli stand-by is set, i-
a
ppli appears as stand-by. The image set as
the stand-by display of Set screen does not appear. If i-
a
ppli stand-by
is disabled, the image set as the stand-by display of Set screen
appears.
Web To functions are not available from i-
a
ppli stand-by.
If software that transmits data is set as i-
a
ppli stand-by, the software
may not operate properly depending on the signal strength.
If All lock is set when in i-
a
ppli stand-by, i-
a
ppli stand-by display closes
and [ 待受画面 1] appears.
If i-
a
ppli DX is set as i-
a
ppli stand-by, some i-
a
ppli DX software may
transmit data to verify the validity of the software regardless of the
software Network set.
dr20_E.book 274 ページ ２００９年５月１４日 木曜日 午前１０時１７分