Dell PowerConnect J-SRX100 Hardware Manual Download Page 29

Page: 29 / 158

Figure 5: J-SRX100 Services Gateway Ethernet Port LEDs

The below table applies only to LED marked 1. Table 10 on page 15 provides the states
of this LED.

Table 10: J-SRX100 Services Gateway Built-In Ethernet Port LEDs

Description

State

Color

Function

Link is active. Data
communication is taking
place.

Blinking

Green

TX/RX/LINK

Link is active. No data
communication is taking
place.

Steady

Link is inactive.

Off

Unlit

NOTE:

The LED marked as 2 in the graphic is not functional in this release.

Documentation

J-SRX100 Services Gateway Specifications on page 7

•

J-SRX100 Services Gateway Front Panel and Back Panel Views on page 9

•

J-SRX100 Services Gateway Built-In Interfaces on page 10

•

J-SRX100 Services Gateway Boot Devices on page 15

•

J-SRX100 Services Gateway Power Supply on page 16

J-SRX100 Services Gateway Boot Devices

The J-SRX100 Services Gateway can boot from two devices:

•

Internal flash

•

External USB storage device

Documentation

J-SRX100 Services Gateway Specifications on page 7

•

J-SRX100 Services Gateway Front Panel and Back Panel Views on page 9

•

J-SRX100 Services Gateway Built-In Interfaces on page 10

•

J-SRX100 Services Gateway Power Supply on page 16

Chapter 2: J-SRX100 Services Gateway Hardware Components and Specifications

Summary of Contents for PowerConnect J-SRX100































































































































































Search results

Summary of Contents for PowerConnect J-SRX100

Reviews:

Dell PowerConnect J-SRX100, Hardware Manual, Page: 29 / 158

Search results

Summary of Contents for PowerConnect J-SRX100

Reviews: