Dell PowerConnect J-SRX100 Hardware Manual Download Page 24

Page: 24 / 158

J-SRX100 Services Gateway Back Panel

Figure 3 on page 10 illustrates the back panel of the J-SRX100 Services Gateway.

Figure 3: J-SRX100 Services Gateway Back Panel

Table 7 on page 10 lists the components available on the back panel of the J-SRX100
Services Gateway.

Table 7: J-SRX100 Services Gateway Back Panel

Component

Number

Lock

Grounding point

Cable tie holder

Power supply point

NOTE:

The cable tie holder provides support for holding the power cord on

the power supply point.

The lock provides the option to lock and secure the device to the installation
site.

Documentation

J-SRX100 Services Gateway Specifications on page 7

•

J-SRX100 Services Gateway Built-In Interfaces on page 10

•

J-SRX100 Services Gateway LEDs on page 12

•

J-SRX100 Services Gateway Boot Devices on page 15

•

J-SRX100 Services Gateway Power Supply on page 16

J-SRX100 Services Gateway Built-In Interfaces

Table 8 on page 11 summarizes the interface ports supported on the J-SRX100 Services
Gateway.

PowerConnect J-SRX100 Services Gateway Hardware Guide

Summary of Contents for PowerConnect J-SRX100































































































































































Search results

Summary of Contents for PowerConnect J-SRX100

Reviews:

Dell PowerConnect J-SRX100, Hardware Manual, Page: 24 / 158

Search results

Summary of Contents for PowerConnect J-SRX100

Reviews: