Datalogic AV7000, Reference Manual

Page: 314 / 337

AV7000 LINEAR CAMERA REFERENCE MANUAL
302
7
e-Genius
Description
Type Explanation Possible Cause Solution
Decoder board over
temperature Warning The Decoder board has
exceeded the maximum
temperature. Ambient temperature has
exceeded the maximum
50 degrees C operating
temperature. There is a
fan failure or airflow
blockage. Verify the ambient temperature
is less than or equal to 50 C.
Check the fan operation and
for any airflow obstructions.
Replace fans if necessary.
Decoder CPU over
temperature Warning The Decoder CPU
exceeding the maximum
temperature. Ambient temperature has
exceeded the maximum
50 degrees C operating
temperature. There is a
fan failure or airflow
blockage. Verify the ambient temperature
is less than or equal to 50 C.
Check the fan operation and
for any airflow obstructions.
Replace fans if necessary.
Distance to Scanline
too small Warning The distance from the
position sensor scan
line to the closest point
of the camera line of
sight is too small. The position sensor is
mounted incorrectly,
too close to the
camera. The camera is
mounted incorrectly or
the angle is wrong. Verify and move the position
sensor further upstream if
needed. Verify and move the
camera further downstream
if needed. Verify and correct
the camera angle if needed.
IV State Not Sent - Pkg
Not Found Warning A trigger message for a
package was received
but the package was
never found in the
image data. This can occur during
boot up if packages are
running through the
tunnel or if a package is
completely shadowed. Contact Datalogic Support if
this error persists.
RangeFinder is not
Expected Warning A RangeFinder is
detected in the system
but is not selected as the
position sensor. Wrong position sensor is
selected in the
configuration. Select the RangeFinder as the
position sensor in the
configuration.
RangeFinder is not OK Warning The RangeFinder is
online but reporting an
error. Check the RangeFinder
GUI page for error
details. Check the RangeFinder GUI
page for error details. Refer
the RangeFinder error list for
more information.
Real-time Processor
has Warnings Warning The Real-Time
Processor is reporting
at least one warning. Check the Real-Time
Processor section of
the
Modify Settings |
System Info > Device
Details
window
for
detailed warning
information
(See
section 0 ).
Check the Real-Time
Processor section of the
Modify Settings | System
Info > Device Details
window for detailed warning
information
(See section 0 ).
Refer to the Real-Time
Processor warning list for
more information.
Software upgrade in
progress Warning The camera is in the
process of updating
software. A software update was
loaded on this camera
or one of the cameras
in the tunnel and auto-
update is enabled. Wait for the update to
complete.
Unable to mount
SMB/CIFS file share for
image saving Warning The camera was
unable to mount the
SMB/CIFS file share on
the external device. File System parameters
on the Modify Settings |
Global Settings | Image
Saving Destination
Settings window are not
correct
(See section
4.5.7 ) . External device
is not available. The
Server Path is set to a
path local to the
camera.
Make sure the File System
parameters on the Modify
Settings | Global Settings |
Image Saving Destination
Settings window are properly
set
(See section 4.5.7 ) .
Make sure the Server Path
is not local to the camera.
Unexpected Camera is
Online Warning A camera is detected in
the tunnel that was not
part of the tunnel
configuration. A new camera was
added to the tunnel or an
existing camera was
replaced. Add the camera to the
configuration and proceed with
the set up if it is a new
camera. If an existing camera
was replaced, there should be
an offline camera. From the
Modify Settings | System Info,
replace the offline camera with
one listed outside the cluster
(See section 4.4).
Decoder load warning Info Decode engine CPU
usage is high. Background is noisy.
Multiple 2D codes are
enabled. Camera gain is
too low or too high or the
camera is out of focus. Make sure gain and focus are
set properly. Otherwise this
error will not cause any
problems.