Daikin RXSQ24TAVJU, Service Manual

Page: 105 / 311

SiUS331708EA Field Settings from Remote Controller
Field Settings and Test Operation 92
Notes :
1. Settings are made simultaneously for the entire group, however, if you select the mode No. inside
parentheses, you can also set by each individual unit. Setting changes however cannot be checked except in
the individual mode for those in parentheses.
∗
2. The mode numbers inside parentheses cannot be used by wireless remote controllers, so they cannot be set
individually. Setting changes also cannot be checked.
3. Do not make settings other than those described above. Nothing is displayed for functions the indoor unit is
not equipped with.
4. 88 or Checking the connection. Please stand by. may be displayed to indicate the remote controller is
resetting when returning to the normal mode.
∗
5. If the setting mode to “Equipped”, energy recovery ventilator fan conducts the fan residual operation by
linking to indoor unit.
∗
6. Only for FXTQ-TA models
∗
7. Only for FXDQ-M, FXTQ-TA, CXTQ-TA models
∗
8. If the airflow setting when thermostat is OFF is set to OFF (12(22)-3-03, 12(22)-6-03), the air in the indoor
unit will be stagnant and suction air thermistor may not detect room temperature correctly, resulting in
problems that thermostat will not be ON easily.
Use optional remote sensor in such conditions, or set the field setting 10(20)-2 to
03 (only remote controller
thermistor).
∗
9. Only for FXFQ-T and FXUQ-P sensing models
∗
10.Only for CXTQ-TA models
∗
11.Only for FXTQ-TA and CXTQ-TA models
∗
12.Only for FXDQ-M models
∗
13.Only for FXEQ-P models
∗
14.Only for FXZQ-TA and FXSQ-TA models
Mode
No.
(
∗
2)
First
Code
No.
Setting Contents
Second Code No.
01 02 03 04
13(23)
0 Setting of airflow rate Refer to page 103 for details.
1
Airflow direction setting
(Set when a blocking pad kit has been installed.)
F (4 directions) T (3 directions)
W
(2 directions)
—
2 (
∗
9) Swing pattern settings
All direction
synchronized swing
— Facing swing —
3 (
∗
13) Operation of downward flow flap Equipped Not equipped — —
4 Setting of airflow direction adjustment range Draft prevention Standard
Ceiling soiling
prevention
—
5 (
∗
10) CFM table setting Standard Low — —
5 (
∗
12) Setting of static pressure selection Standard High static pressure — —
6 External static pressure settings Refer to page 105 for details.
14
(24)
4 (
∗
11)
Optional kit setting (UV lamp + humi
economizer)
Refer to page 106 for details.
5 (
∗
11) Residential dry
Set temperature:
room temperature
Set temperature:
same as cooling set
temperature
— —
9 (
∗
13) Mold proof operation setting Standard
For high humidity
areas
— —
11 (
∗
10) Gas furnace test mode OFF Low heat High heat —
15(25)
0 Drain pump operation settings — ON OFF —
1 Humidification when heating thermostat is OFF Not equipped Equipped — —
2
Setting of direct duct connection
(when the indoor unit and energy recovery
ventilator unit are connected by duct directly.)
(
∗
5)
Not equipped Equipped — —
3
Interlocked operation between humidifier and
drain pump
Not interlocked Interlocked — —
5 Individual setting of ventilation Not individual Individual — —
1b 3 Display of contact center Displayed Not displayed — —
4 Display of error codes on the remote controller
— Two-digit display —
Four-digit
display
12 Key-lock pattern settings No operation
allowed (Cancel
procedure is
displayed.)
No operation
allowed (Cancel
procedure is not
displayed.)
No menu
operation is
allowed
(Cancel
procedure is
displayed.)
No menu
operation is
allowed any
time.
14 Setting "restricted / permitted" of airflow block Refer to page 108 for details.
1c 0 Room temperature display Room temperature
is not displayed
Room temperature
is displayed
— —