F
UNCTION
ON
O
PERATION
P
ANEL
W
ELDING
C
ONDITION
C
HAPTER
6
6-6
6.2 Function on Operation Panel
This section explains the function of displays and keys arranged on the operation panel.
No.
Name
Function
1
Left digital meter
Displays various information.
•
The welding current is displayed in welding, and the LED of "A" lights up.
•
In each setting, corresponding setting values are displayed, and the LED lit position
automatically switches.
2
Right digital meter
Displays various information.
•
The welding voltage is displayed in welding.
•
In each setting, corresponding setting values are displayed, and the LED lit position
automatically switches.
3
Parameter adjustment knob
Adjusts each parameter value such as welding current.
4
PARAMETER SELECT keys
Switches the welding sequence as the set target. In welding, also switches the display to
the value set in the welding condition being used for welding.
5
F (function) key
Sets the internal function of welding power source. (
6.10
-
Setting Internal Functions)
Pressing this key for a second or more lights up the LED, and the sequence transits to the
Internal Function Setting mode.
6
GAS CHECK key
Discharges the shield gas. (
5.3
-
Power ON and Gas Supply)
Pressing this key makes the LED lit, allowing the shield gas to be discharged.
After discharging the gas for approximately 2 minutes automatically stops the discharge.
Pressing this key again lights off the LED, stopping the shield gas discharge.
7
TORCH key
Selects whether to use the air-cooled welding torch or the water-cooled welding torch.
Press the key to switch over each mode.
•
LED ON: Water-cooled welding torch mode
•
LED OFF: Air-cooled welding torch mode
8
WELDING METHOD key
Select the type of welding method.
To select AC STICK welding, hold down the WELDING METHOD key for 3 seconds while the
DC TIG mode is selected.
•
The LED of the parameter in selection lights up
9
AC WAVEFORM key
Selects the type of AC welding waveform to use.
•
For details of AC waveform (
6.7.2 Setting AC waveform)
10
CRATER-FILL key
Select the crater treatment method or arc spot at the end of welding.
The LED of the parameter in selection lights up.
•
For details of the crater treatment (
6.6.3
-
Crater setting)
•
For details of arc spot (
6.6.5
-
Arc spot time)
OFF
ON
SPOT
REPEAT
AC-DC FREQ.
SYNERG.
A C
FREQ.
AC TIG
AC-DC TIG
DC TIG
AC STICK
DC STICK
3sec.
A C
WAVE
A
sec.
Hz
mm
%
JOB No.
DC NO-LOAD VOLTAGE
V/
Φ
CRATER-FILL.
CURR.
INITIAL CURR.
PULSE CURR.
PULSE FREQ.
UP SLOPE
DOWN SLOPE
GAS
WATER
TORCH
SPOT TIME
STANDARD
SOFT
HARD
ON
ON
ON
AC BALANCE
PULSE
ON
ON
CURRENT ADJ.
LIFT START
INITIAL CURR.
SLOPE
WELD
MONITOR
WELDING CURR.
(BASE CURR.)
WARNING
WELDING
METHOD
CRATER
-FILL
28
19
7
6
5
23
24
4
4
1
2
25
26
16
17
22
3
21
15
18
12
13
14
11
10
9
8
27
20
Summary of Contents for Welbee WB-A350P
