CONTROL SOLUTIONS ValuPoint 4 User Manual Download

Page: 70 / 95

Vendor_Identifier (120)

Unsigned16
(should always return 208)

Model_Name (70)

CharacterString

Fimrware_Revision (44)

CharacterString

Application_Software_Version
(12)

CharacterString

Protocol_Version (98)

Unsigned

Protocol_Revision (139)

Unsigned

Protocol_Services_Supported (97) BACnetServicesSupported

Protocol_Object_Types_Supported
(96)

BACnetObjectTypesSupported

Object_List (76)

BACnetARRAY[N] of BACnetObjectIdentifier

Max_APDU_Length_Accepted (62) Unsigned

Segmentation_Supported (107)

BACnetSegmentation

APDU_Timeout (11) (W)

Unsigned

Number_Of_APDU_Retries (73)
(W)

Unsigned

Device_Address_Binding (30)

List of BACnetAddressBinding

Database_Revision (155)

Unsigned

Max_Master (64) (W)

Unsigned

Max_Info_Frames (63) (W)

Unsigned

Location (58) (W)

CharacterString

Max_Segments_Accepted (167)

Unsigned

APDU_Segment_Timeout (10)
(W)

Unsigned

Active_COV_Subscriptions (152)

List of BACnetCOVSubscription

Last_Restart_Reason (196)

BACnetRestartReason

Local_Time (57) (W)

Time

Local_Date (56) (W)

Date

UTC_Offset (119) (W)

INTEGER

Daylight_Savings_Status (24) (W) BOOLEAN

12. Object Properties

file:///C:/AAA_CSI/Literature/2016 User Guides/VP4-BACnet User Gui...

5 of 7

11/3/2016 10:43 AM

Summary of Contents for ValuPoint 4
































































































Search results

Summary of Contents for ValuPoint 4

Reviews:

Related manuals for ValuPoint 4

Brands by name

Popular brands

CONTROL SOLUTIONS ValuPoint 4, User Manual

Search results

Summary of Contents for ValuPoint 4

Reviews:

Related manuals for ValuPoint 4

Brands by name

Popular brands