manualshive.com logo in svg

CONTROL SOLUTIONS ValuPoint 4, User Manual

Share
Download
CONTROL SOLUTIONS ValuPoint 4 User Manual Download Page 24

select the device that you wish to configure. By the time you switch to this tab after
connecting (Connect tab), it is common to see some devices already listed. You can
click ‘Send Who-Is’ any number of times to send out another request for devices to
identify themselves.

The Who-Is only locates devices and lists them as illustrated in the first screen shot
above. You need to use Refresh to get the object models and names.

The MAC address of MS/TP devices found will be listed in the Net Address column. IP
devices on the other side of a router will also be shown, but at the same MAC address
- this will be the MAC address of the router. Additional network information is recorded
internally and the configuration tool will use this information as needed to access the
devices on the other side of the router.

4.2       Refresh

Click ‘Refresh’ to see which devices have responded. Click ‘Refresh’ at least twice to
cause the tool to request object model and name from each responding device. The
‘Send Who-Is’ sends out the who-is request, and ‘Refresh’ sends out read requests for
model and name for any MAC that has not already been queried for this information.
Following successful refresh, the screen will appear as illustrated below.

4.3       Select Target

4. Who-Is

file:///C:/AAA_CSI/Literature/2016 User Guides/VP4-BACnet User Gui...

2 of 6

11/3/2016 10:40 AM

Summary of Contents for ValuPoint 4
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands