manualshive.com logo in svg

CONTROL SOLUTIONS ValuPoint 4, User Manual

Share
Download
CONTROL SOLUTIONS ValuPoint 4 User Manual Download Page 45

               Discrete, active low
               Dry contact, active open
               Dry contact, active closed
               Pulse, high speed
               Pulse, low speed (no hi-res)
               Resistance, high resolution
               Resistance, low resolution
               Position pot, hi-res, 1K-30K
               Position pot, lo-res, 1K-30K

               Thermistor, 10K type III hi-res, F
               Thermistor, 10K type II hi-res, F
               Thermistor, 3K type II hi-res, F
               Thermistor, 20K type IV hi-res, F
               Thermistor, 5K type II hi-res, F
               Thermistor, 10K type III hi-res, C
               Thermistor, 10K type II hi-res, C
               Thermistor, 3K type II hi-res, C
               Thermistor, 20K type IV hi-res, C
               Thermistor, 5K type II hi-res, C

               Thermistor, 10K type III lo-res, F
               Thermistor, 10K type II lo-res, F
               Thermistor, 3K type II lo-res, F
               Thermistor, 20K type IV lo-res, F
               Thermistor, 5K type II lo-res, F
               Thermistor, 10K type III lo-res, C
               Thermistor, 10K type II lo-res, C
               Thermistor, 3K type II lo-res, C
               Thermistor, 20K type IV lo-res, C
               Thermistor, 5K type II lo-res, C

The designation hi-res and lo-res refer to the A/D resolution. There are two types
of A/D in the ValuPoint. The 'hi-res' A/D is a delta-sigma integrating converter that
produces 15-bit results (16-bit including sign, which is always positive with the input
circuitry implemented). The 'lo-res' A/D is a fast successive approximation converter
which produces 10-bit results.

Due to the fact that 'hi-res' conversion is relatively slow (about 1/4 second compared
to a few microseconds for lo-res), some combinations of I/O are not possible. Low
speed pulse counting to 10Hz is only possible when all inputs are in lo-res mode. All
discrete or dry contact modes are lo-res. High speed pulse counting (to 1kHz) is
possible with any combination of modes; however high speed counting uses dedicated
hardware and is only available in inputs channels 13 and 14.

Low speed pulse counting in combination with hi-res input conversions is possible, but
input pulse rate is limited to about 2Hz. To increase this limit to 10Hz, all analog

8. Object Map Page

file:///C:/AAA_CSI/Literature/2016 User Guides/VP4-BACnet User Gui...

5 of 10

11/3/2016 10:42 AM

Summary of Contents for ValuPoint 4
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands