manualshive.com logo in svg

CONTROL SOLUTIONS ValuPoint 4, User Manual

Share
Download
CONTROL SOLUTIONS ValuPoint 4 User Manual Download Page 69

(4) Real (floating point),
(8) Bit string,
(9) Enumerated

Slave _Bit_Position (826)
(W)

ENUMERATED

Slave_Address (827) (W)

ENUMERATED
(MAC address if BACnet slave does not support
dynamic binding)

Error_Class (830)

Unsigned

Error_Code (831)

Unsigned

Config_Write_Command
(832) (W)

ENUMERATED
(1) write config to EEPROM

Hardware_Configuration
(841) (W)

ENUMERATED

Hardware_Qualifier_1 (842)
(W)

ENUMERATED

Hardware_Qualifier_2 (843)
(W)

ENUMERATED

Feedback (848)

Unsigned

Raw_Data (849)

Unsigned

12.2 Device Object Properties

The following properties are found in the Device object of the ValuPoint. In addition to
standard Device properties, configuration properties that apply at a system level to the
whole device are included here.

Property

Encoding

Object_Identifier (75) (W)

BACnetObjectIdentifier

Object_Name (77) (W)

CharacterString

Object_Type (79)

BACnetObjectType
ENUMERATED:
device (8)

System_Status (112)

BACnetDeviceStatus

Vendor_Name (121)

CharacterString

12. Object Properties

file:///C:/AAA_CSI/Literature/2016 User Guides/VP4-BACnet User Gui...

4 of 7

11/3/2016 10:43 AM

Summary of Contents for ValuPoint 4
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands