manualshive.com logo in svg

CONTROL SOLUTIONS ValuPoint 4, User Manual

Share
Download
CONTROL SOLUTIONS ValuPoint 4 User Manual Download Page 44

8.2       Physical Hardware I/O Parameters

Map Physical I/O (check box) – Check this box to map the displayed BACnet object to
a physical I/O point. The I/O point that has been set to be associated with this object
will appear in the Physical Point window to the right. To change the association
between I/O points and BACnet objects, go to the I/O List page and make changes
there. If an object has already been mapped by checking this box, be sure to uncheck
it first to release the object for reassignment before making changes on the I/O List
page.

Configuration Option – Select the I/O configuration desired for the physical point. This
only applies to A/UI analog/universal input points. The A/UI inputs may function as
any of the following:

               0-10V, high resolution
               0-10V, low resolution
               4-20mA, high res with resistor
               4-20mA, low res with resistor
               Discrete, active high

8. Object Map Page

file:///C:/AAA_CSI/Literature/2016 User Guides/VP4-BACnet User Gui...

4 of 10

11/3/2016 10:42 AM

Summary of Contents for ValuPoint 4
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands