Cisco SF550X-24 Administration Manual Download Page 383 | Manualshive

Page: 383 / 725

background image

IP Configuration

IPv6 Management and Interfaces

293

Cisco Sx350, SG350X, SG350XG, Sx550X & SG550XG Series Managed Switches, Firmware Release 2.2.5.x

15

The following types of tunnels can be configured on the device:

•

ISATAP Tunnel

The Intra-Site Automatic Tunnel Addressing Protocol (ISATAP) is a point-to-multi-
point tunnel. The source address is the IPv4 address (or one of the IPv4 addresses) of
the device.

When configuring an ISATAP tunnel, the destination IPv4 address is provided by the
router. Note that:

•

Manual Tunnel

-

An IPv6 link local address is assigned to the ISATAP interface. The initial IP
address is assigned to the interface, which is then activated.

-

If an ISATAP interface is active, the ISATAP router IPv4 address is resolved via
DNS by using ISATAP-to-IPv4 mapping. If the ISATAP DNS record is not
resolved, ISATAP host name-to-address mapping is searched in the host mapping
table.

-

When the ISATAP router IPv4 address is not resolved via the DNS process, the
ISATAP IP interface remains active. The system does not have a default router for
ISATAP traffic until the DNS process is resolved.

This is a point-to-point definition. When creating a manual tunnel, you enter both the
source IP address (one of the device’s IP addresses) and the destination IPv4 address.

•

6-4 Tunnel

6to4 is an automatic tunneling mechanism that uses the underlying IPv4 network as a
non-Broadcast multiple-access link layer for IPv6. Only one 6to4 tunnel is supported
on a device.

The 6to4 tunnel is supported only when IPv6 Forwarding is supported.

IPv6 Multicast is not supported on the 6to4 tunnel interface.

The switch automatically creates a 2002::/16 on-link prefix on the 6to4 tunnel. The
connected 2002::/16 route on the tunnel is added to the Routing Table as result of the
on-link prefix creation.

When the tunnel mode is changed from 6to4 to another mode, the on-link prefix and
connected routes are removed.

When the next hop outgoing interface is the 6to4 tunnel, the IPv4 address of the next
hop node is taken from the prefix 2002:WWXX:YYZZ::/48 of the IPv6 next hop IPv6
address, if it is global, and from the last 32 bits of the interface identifier of the IPv6
next hop IPv6 address, if it is link local.

«
...
381
382
383
384
385
...
»

Summary of Contents for SF550X-24






















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SF550X-24

Brand: S&C Pages: 26

Brand: S&C Pages: 37

Brand: S&C Pages: 28

Brand: CAME Pages: 2

Brand: Broadcast Tools Pages: 28

Brand: Teseq Pages: 60

Brand: SMART-AVI Pages: 2

Sierra Video 1208V3S

Brand: Kramer Pages: 2

Brand: Cabletron Systems Pages: 120

Brand: Fairchild Pages: 20

Brand: Televes Pages: 24

GlobeCaster STUDIO 4000

Brand: Global Streams Pages: 144

TNM4000-TP36FF4X16G24P

Brand: MRD Pages: 38

Brand: Velleman Pages: 8

Brand: HDTV Supply Pages: 21

Brand: tactio Pages: 2

Brand: Inline Pages: 4

Sun Datacenter InfiniBand Switch 36

Brand: Sun Oracle Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands