manualshive.com logo in svg

Cisco MDS 9000 Series, Command Reference Manual

Share
Download
Cisco MDS 9000 Series Command Reference Manual Download Page 1056

S e n d   d o c u m e n t a t i o n   c o m m e n t s   t o   m d s f e e d b a c k - d o c @ c i s c o . c o m

21-118

Cisco MDS 9000 Family Command Reference

OL-18089-01, Cisco MDS NX-OS Release 4.x

Chapter 21      S Commands

    system health module

Defaults

The default for OHMS is enabled.

The CRC Checksum test is enabled to automatically run in the background every 7 days.

The firmware update is enabled to automatically run in the background every 30 days.

The 

failure-action

 feature is enabled.

Command Modes

Configuration mode.

Command History

Usage Guidelines

The

 

CRC checksum test and the firmware update can be enabled on the following modules:

  •

DS-X9016

  •

DS-X9032

  •

DS-X9302-14K9

  •

DS-X9308-SMIP

  •

DS-X9304-SMIP

  •

DS-X9530-SF1-K9

If you do not configure the loopback frequency value, the default frequency of 5 seconds is used for all 
modules in the switch.

Examples

The following example enables the battery-charger test on both batteries in the CSM module. If the 
switch does not have a CSM, this message is issued:

switch# 

config terminal

switch(config)# system health module 6 battery-charger

battery-charger test is not configured to run on module 6.

The following example enables the cache-disk test on both disks in the CSM module. If the switch does 
not have a CSM, this message is issued:

switch(config)# 

system health module 6 cache-disk

cache-disk test is not configured to run on module 6.

The following example enables the bootflash test.

switch(config)# 

system health module 6 bootflash

System health for module 6 Bootflash is already enabled.

The following example enables you to prevent the NX-OS software from taking any action if any 
component fails.

switch(config)# 

system health module 6 bootflash failure-action

System health failure action for module 6 Bootflash test is now enabled.

The following example enables an already-enabled bootflash test.

Release

Modification

1.3(4) 

This command was introduced.

3.1(3)

Added the 

cf-crc-check

 and 

cf-reflash

 options.

Summary of Contents for MDS 9000 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands