Cisco MDS 9000 Series Command Reference Manual Download Page 1024 | Manualshive

Page: 1024 / 1640

background image

S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m

21-86

Cisco MDS 9000 Family Command Reference

OL-18089-01, Cisco MDS NX-OS Release 4.x

Chapter 21 S Commands

switchport

The EISL encapsulation is disabled.

The default receive data buffer size is 2112 bytes.

The port mode is

auto

.

The speed is

auto

.

The maximum auto speed is

2000

.

The trunk mode is

on

.

The rate mode is

shared

.

Command Modes

Interface configuration submode.

Command History

Usage Guidelines

You can specify a range of interfaces by issuing a command with the following example format:

interface

space

fc1/1

space

-

space

5

space

,

space

fc2/5

space

-

space

7

Tip

The

shutdown

or

no shutdown

command for the FCIP or iSCSI interfaces is automatically issued when

you change the MTU size—you do not need to explicitly issue this command.

You must perform the

fcrxbbcredit extended enable

command in configuration mode to use the

switchport fcrxbbcredit extended

command in interface configuration submode to enable extended

BB_credits on a Fibre Channel interface.

The port speed on an interface, combined with the rate mode, determines the amount of shared resources
available to the ports in the port group. Especially in the case of dedicated rate mode, the port group
resources are reserved even though the bandwidth is not used. For example, if an interface is configured
for autosensing (

auto

), then 4 Gbps of bandwidth is reserved even though the maximum operating speed

is 2 Gbps. For the same interface, if autosensing with a maximum speed of 2 Gbps (

auto max 2000

) is

configured, then only 2 Gbps of bandwidth is reserved and the unused 2 Gbps is shared with the other
interface in the port group.

Release

Modification

NX-OS 4.1(3)

Added the

F

and

NP

port mode.

1.0(2)

This command was introduced.

2.0(1b)

Added the

extended

option to the

fcrxbbcredit

keyword.

3.0(1)

•

Added the

fcbbscn

option.

•

Added the

ST

option to the

mode

keyword.

•

Added the

4000

option to the

speed

keyword.

•

Added the

auto

max 2000

option to the

speed

keyword.

•

Added the

rate-mode

keyword.

•

Added the Gigabit Ethernet interface syntax.

•

Added the management interface syntax.

«
...
1022
1023
1024
1025
1026
...
»

Summary of Contents for MDS 9000 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MDS 9000 Series

Brand: Bacharach Pages: 64

Brand: LaserLine Pages: 24

Brand: Tascam Pages: 4

Brand: Harpers Pages: 8

Brand: NARDA Pages: 64

Brand: VEE GEE Pages: 2

Brand: Veeder-Root Pages: 39

Brand: Veeder-Root Pages: 98

Brand: VECTECH Pages: 9

Brand: JRC Pages: 308

Brand: RIDGID Pages: 18

Brand: Dynojet Pages: 88

Brand: VP instruments Pages: 15

Brand: IDEAL Pages: 84

Brand: Hanna Instruments Pages: 2

Brand: Zero 88 Pages: 32

Brand: MULTISPAN Pages: 4

Brand: PASI Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands