Cisco ASR 907 Hardware Installation Manual Download Page 110

Page: 110 / 204

Figure 56: Connecting a Modem to the Cisco ASR 907 Router

RJ45 to DB-9

RJ45 AUX port

Modem

DB-9 to DB-25 adapter

Step 2

Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter.

Step 3

Connect the DB-25 end of the modem adapter to the modem.

Step 4

Make sure that your modem and the router auxiliary port are configured for the same transmission speed (up
to 115200 bps is supported) and for mode control with data carrier detect (DCD) and data terminal ready
(DTR) operations.

Cisco ASR 907 Router Hardware Installation Guide

100

Installing the Cisco ASR 907 Router

Connecting to the Auxiliary Port

Summary of Contents for ASR 907












































































































































































































Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands

Cisco ASR 907, Hardware Installation Manual

Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands