Cisco ASR 907 Hardware Installation Manual Download Page 97

Page: 97 / 204

Figure 53: Power Supply with Lead Wires

Positive (+) lead wire

2,
4

Negative (-) lead wire

1,
3

Do not overtorque the fasteners of the terminal block. The recommended maximum torque is from
25 in.-lb (2.82 N-m).

Caution

Step 6

Use a tie wrap to secure the wires to the rack, so that the wires are not pulled from the terminal block by casual
contact. Make sure the tie wrap allows for some slack in the wire.

Activating the DC Power Supply

Perform the following procedure to activate the DC power supply:

Procedure

Step 1

Remove the tape from the circuit-breaker switch handle, and restore power by moving the circuit-breaker
switch handle to the On (|) position.

Step 2

Verify power supply operation by checking if the power supply front panel LEDs are in the following states:

• INPUT OK LED is green
• OUTPUT FAIL LED is green

Cisco ASR 907 Router Hardware Installation Guide

Installing the Cisco ASR 907 Router

Activating the DC Power Supply

Summary of Contents for ASR 907












































































































































































































Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands

Cisco ASR 907, Hardware Installation Manual

Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands