Cisco ASR 907 Hardware Installation Manual Download Page 191 | Manualshive

Page: 191 / 204

background image

reach. Within the multimode category, only short reach is available. For information about optical SFP modules,
see the documentation for the SFP module at

http://www.cisco.com/en/US/partner/products/hw/modules/ps5455/prod_installation_guides_list.html

LED Summary

The following sections describe the meanings of the LEDs on the Cisco ASR 907 Router.

RSP LEDs

The table below summarizes the RSP LEDs.

A major alarm condition indicates the failure of a single fan in the fan tray; a critical alarm indicates the failure
of multiple fans. In the event that a single fan fails, the Cisco ASR 907 Router software adjusts the fan speed
to prevent excessive heat within the chassis.

Note

ASR900-RSP LED

Table 33: RSP LEDs

Description (two LEDs for each port)

Color/State

LED

Disabled/no power to RSP

Off

Power (PWR)

Power rails on RSP in range

Green

Disabled/power down

Off

Status (STAT)

Failure to boot (lit at reset)

Red

Rommon booted

Yellow

IOS booted and running

Green

Not available

Off

Active (ACT)

Standby (indicates standby RSP)

Yellow

Active (indicates active RSP)

Green

No connection

Off

Management port (MGMT)

Connected with no activity

Green

Connected with activity

Flashing green

Cisco ASR 907 Router Hardware Installation Guide

181

Troubleshooting

LED Summary

«
...
189
190
191
192
193
...
»

Summary of Contents for ASR 907













































































































































































































Reviews:

No comments

Related manuals for ASR 907

Brand: Barracuda Networks Pages: 2

Brand: TDC Pages: 27

Brand: Mafell Pages: 162

Brand: DPtech Pages: 39

Brand: KPN Pages: 14

Brand: ZyXEL Communications Pages: 5

Brand: AirTies Pages: 28

PG-Flex FLC-704

Brand: PairGain Pages: 20

B-Control Fader BCF2000

Brand: Behringer Pages: 13

Brand: RR-Concepts Pages: 12

Brand: Belkin Pages: 42

Brand: Tektronix Pages: 143

Brand: Epson Pages: 71

Brand: Epson Pages: 29

Brand: Epson Pages: 57

C823312 (Ethernet)

Brand: Epson Pages: 76

2 Channel Inductor Module CLX-2IND

Brand: Crestron Pages: 1

Brand: KTI Networks Pages: 147

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands