Cisco ASR 907 Hardware Installation Manual Download Page 197

Page: 197 / 204

Table 37: 16 T1/E1 Interface Module LEDs

Description (two LEDs for eachT1/E1 port)

Color/State

LED

Active

Green

Active

Standby

Blinking green

Operationally down; card is disabled or shut down

Off

All ports up

Green

Port

All ports up and one or more ports in a loopback state

Blinking green

One or more configured ports are down

Amber

One or more configured ports are down and at least one configured port is in a
loopback state

Blinking amber

All ports disabled or shut down

Off

All power rails are within supported range

Green

PWR

Disabled

Red

No power on the interface module

Off

Failed

Red

STAT

Disabled or powered down

Off

Booting

Blinking red

Active

Green

The table below summarizes the LEDs for the 8 T1/E1 interface module.

Table 38: 8 T1/E1 Interface Module LEDs

Description (two LEDs for eachT1/E1 port)

Color/State

LED

Active

Green

Active

Standby

Blinking green

Operationally down; card is disabled or shut down

Off

Cisco ASR 907 Router Hardware Installation Guide

187

Troubleshooting

T1/E1 Interface Module LEDs

Summary of Contents for ASR 907












































































































































































































Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands

Cisco ASR 907, Hardware Installation Manual

Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands