Cisco ASR 907 Hardware Installation Manual Download Page 194

Page: 194 / 204

Table 35: Interface Module LEDs

Description

Color/State

LED

Disabled/no power to IM

Off

Power (PWR)

Enabled and power rails on IM in range

Green

Disabled/power-down

Off

Status (STAT)

Failure (on at reset)

Red

Booting (if local CPU)

Flashing Red

Operational

Green

Inactive or no connection

Off

Link status (L)

Fault/loop condition

Amber

Ok with activity or no activity

Green

Inactive port status

Off

Speed (S)

Activity or no activity

Green

1-Port OC-192 or 8-Port Low Rate CEM Interface Module LEDs

The table summarizes the LEDs for the 1-Port OC-192 or 8-Port Low Rate CEM Interface Module.

Meaning (Default=Off)

Color/State

LED

All power rails are within spec

Green

Power (PWR)

Disabled

Red

No power to IM

Off

Operational

Green

Operating Status (STAT)

Failure

Red

Disabled or power-down

Off

Link Up

Solid Green

SFP Link (Left LED)

Link Activity

FLASH Green

Fault or Error or Alarm

Solid Yellow

RFU

FLASH Yellow

Disabled or No Link

Off

Cisco ASR 907 Router Hardware Installation Guide

184

Troubleshooting

1-Port OC-192 or 8-Port Low Rate CEM Interface Module LEDs

Summary of Contents for ASR 907












































































































































































































Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands

Cisco ASR 907, Hardware Installation Manual

Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands