Cisco ASR 907 Hardware Installation Manual Download Page 96

Page: 96 / 204

Tools and Equipment

• Dual-hole lugs

• Double barrel with inspection hole

• Hole spacing is 5/8 in.

• Lug tab width max 0.46 in.

• Nuts

• PSU can accommodate 10 – 6 AWG

• Number 2 Phillips Screwdriver

• 7 mm nut driver or 7 mm socket on a torque wrench

Procedure

Step 1

Locate the terminal block on the power supply unit.

Step 2

Flap open the front protective cover on the power supply unit.

Step 3

Use a wire-stripping tool to strip the ends of each of the two wires coming from the DC-input power source
as recommended by the lug manufacturer.

Stripping more than the recommended amount of wire can leave behind exposed wire from the
terminal block after installation.

Note

Step 4

Identify the positive and negative feed positions for the terminal block. The recommended wiring sequence
is as in the figure below.

Step 5

Attach the lugs on the terminal block, see the figure below.

Cisco ASR 907 Router Hardware Installation Guide

Installing the Cisco ASR 907 Router

Tools and Equipment

Summary of Contents for ASR 907












































































































































































































Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands

Cisco ASR 907, Hardware Installation Manual

Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands