Cisco ASR 907 Hardware Installation Manual Download Page 60

Page: 60 / 204

Date

Verified By

Task

Types and numbers of interfaces verified

Safety recommendations and guidelines reviewed

Installation Checklist copied

Site Log established and background information entered

Site power voltages verified

Site environmental specifications verified

Required passwords, IP addresses, device names, and so on, available

Required tools available

Network connection equipment available

Cable-management brackets installed (optional, but recommended)

AC power cables connected to AC sources and router

DC power cables connected to DC sources and router

Network interface cables and devices connected

System power turned on

System boot complete (STATUS LED is on)

Shared port adapters are operational

Correct software configuration displayed after system banner appears

Creating a Site Log

The Site Log provides a record of all the actions related to installing and maintaining the router. Keep it in
an accessible place near the chassis so that anyone who performs tasks has access to it.

Create the Site Log prior to the installation. See

Site Log and Manufactures

for more information on the Site

Log as well as a sample Site Log that can be used to make copies.

Receiving the Cisco ASR 907 Router

Each Cisco ASR 907 Router chassis is shipped in a container. See the figure below.

Cisco ASR 907 Router Hardware Installation Guide

Preparing for Installation

Creating a Site Log

Summary of Contents for ASR 907












































































































































































































Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands

Cisco ASR 907, Hardware Installation Manual

Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands