Cisco ASR 907 Hardware Installation Manual Download Page 196

Page: 196 / 204

Meaning (Default=Off)

Color/State

LED

All ports are UP

Solid Green

Port Status (PORT)

All ports are UP and one or more ports are in
loopback

FLASH Green

All least one port is down

Solid Amber

One or more ports are down and one or more
ports are in Loopback

FLASH Amber

All ports are disabled or shut down

Off

Interface Module is Active

Solid Green

Activity Status (ACT)

Interface Module is Standby

FLASH Green

No link, interface module is down, disabled
or shut down

Off

OC-3 Interface Module LEDs

The table below summarizes the LEDs for the OC-3 interface module.

Table 36: Interface Module LEDs

Description

Color/State

LED

Disabled/no power to IM

Off

Power (PWR)

Enabled and power rails on IM in range

Green

Disabled/power-down

Off

Status (STAT)

Failure (on at reset)

Red

Booting (if local CPU)

Amber

Operational

Green

SFP receiving good remote signal

Green

Carrier/Alarm (C/A)

Remote or local alarm activated

Yellow

SFP ready and operating normally

Green

Active/Loopback(A/L)

SFP port in loopback state

Yellow

T1/E1 Interface Module LEDs

The table below summarizes the LEDs for the 16 T1/E1 interface module.

Cisco ASR 907 Router Hardware Installation Guide

186

Troubleshooting

OC-3 Interface Module LEDs

Summary of Contents for ASR 907












































































































































































































Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands

Cisco ASR 907, Hardware Installation Manual

Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands