manualshive.com logo in svg

Cisco ASR 907, Hardware Installation Manual

The Cisco ASR 907 is an advanced networking solution that empowers seamless performance with its cutting-edge features. To install this powerful hardware, simply download the user manual for free from our website, where you can easily access the comprehensive Hardware Installation Manual. [Website] offers hassle-free downloads for your convenience.

Share
Download
background image

Site Planning

The following sections describe how to plan for the installation of the Cisco ASR 907 Router:

General Precautions

Observe the following general precautions when using and working with your Cisco ASR 907 Router system:

• Keep your system components away from radiators and heat sources and do not block cooling vents.
• Do not spill food or liquids on your system components and never operate the product in a wet

environment.

• Do not push any objects into the openings of your system components. Doing so can cause fire or electric

shock by shorting out interior components.

• Position system cables and power supply cables carefully. Route system cables and the power supply

cable and plug so that they cannot be stepped on or tripped over. Be sure that nothing else rests on your
system component cables or power cable.

• Do not modify power cables or plugs. Consult a licensed electrician or your power company for site

modifications. Always follow your local and national wiring rules.

• If you turn off your system, wait at least 30 seconds before turning it on again to avoid system component

damage.

Site Planning Checklist

Use the following checklist to perform and account for all the site planning tasks described in this chapter:

• The site meets the environmental requirements.
• The site’s air conditioning system can compensate for the heat dissipation of the Cisco ASR 907 Router.
• The floor space that the Cisco ASR 907 Router occupies can support the weight of the system.
• Electrical service to the site complies with the requirements.
• The electrical circuit servicing the Cisco ASR 907 Router complies with the requirements.
• Consideration has been given to the console port wiring and limitations of the cabling involved, according

to TIA/EIA-232F.

• The Cisco ASR 907 Router Ethernet cabling distances are within limitations.
• The equipment rack in which you plan to install the Cisco ASR 907 Router complies with requirements.
• In selecting the location of the rack, careful consideration has been given to safety, ease of maintenance,

and proper airflow.

Site Selection Guidelines

The Cisco ASR 907 Router requires specific environmental operating conditions. Temperature, humidity,
altitude, and vibration can affect the performance and reliability of the router. The following sections provide
specific information to help you plan for the proper operating environment.

The Cisco ASR 907 Router is designed to meet the industry EMC, safety, and environmental standards
described in the Regulatory, Safety, and Compliance Information for the Cisco ASR 907 Router.

Cisco ASR 907 Router Hardware Installation Guide

39

Preparing for Installation

Site Planning

Summary of Contents for ASR 907













































































































































































































Reviews:

No comments

Related manuals for ASR 907

F5 WANJet 500 Quick Start Card preview
WANJet 500
Brand: F5 Pages: 2
F5 ARX-500 Hardware Reference Manual preview
ARX-500
Brand: F5 Pages: 90
F5 ARX-4000 Parts Replacement Manual preview
ARX-4000
Brand: F5 Pages: 47
National Instruments NI 9219 Operating Instructions Manual preview
NI 9219
Brand: National Instruments Pages: 36
Quantum Scalar 50 Upgrade Instructions preview
Scalar 50
Brand: Quantum Pages: 20
Rajant Corporation BreadCrumb CX1 User Manual preview
BreadCrumb CX1
Brand: Rajant Corporation Pages: 40
NETGEAR ReadyNAS 3220 Series Datasheet preview
ReadyNAS 3220 Series
Brand: NETGEAR Pages: 4
Softing TH LINK Installation Manual preview
TH LINK
Brand: Softing Pages: 16
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Brand: Airvana Pages: 90
Amer.com 8-Port 10/100Mbps Fast Ethernet Switch User Manual preview
8-Port 10/100Mbps Fast Ethernet Switch
Brand: Amer.com Pages: 14
InHand IR615-S Series User Manual preview
IR615-S Series
Brand: InHand Pages: 69
Juniper MX104 Quick Start Manual preview
MX104
Brand: Juniper Pages: 30
ZyXEL Communications ES-105 User Manual preview
ES-105
Brand: ZyXEL Communications Pages: 12
TP-Link VIGI Quick Start Manual preview
VIGI
Brand: TP-Link Pages: 2
ASTRO U 960 Operating Manual preview
U 960
Brand: ASTRO Pages: 12
Adeunis RF ARF8264AAA Quick Start Manual preview
ARF8264AAA
Brand: Adeunis RF Pages: 9
Costar CR4020XDI Installation Manual preview
CR4020XDI
Brand: Costar Pages: 24
Linksys HPES03 User Manual preview
HPES03
Brand: Linksys Pages: 17

Brands by name

Popular brands

Load more brands