Cisco ASR 907 Hardware Installation Manual Download Page 120 | Manualshive

Page: 120 / 204

background image

• If both T1/E1 interfaces are connected to their patch panels in a different configuration (TX to Transmit

and RX to Receive on one interface, and TX to Receive and RX to Transmit on the other interface), use
a T1 straight-through cable (standard RJ45 patch cable) to connect the patch panels.

To comply with the Telcordia GR-1089 NEBS standard for electromagnetic compatibility and safety, connect
the T1/E1 ports only to intra-building or unexposed wiring or cable. The intrabuilding cable must be shielded
and the shield must be grounded at both ends. The intra-building port(s) of the equipment or subassembly
must not be metallically connected to interfaces that connect to the OSP or its wiring. These interfaces are
designed for use as intra-building interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE)
and require isolation from the exposed OSP cabling. The addition of Primary Protectors is not sufficient
protection in order to connect these interfaces metallically to OSP wiring.

Warning

Patch Panel Pinout

Given below are the pinout information for the regular crossover and the straight-through cable patch panel.

Table 10: Pinout Details

Straight-through

Crossover

Pin
#

Transmit Tip

Receive Tip

1

Transmit Ring

Receive Ring

2

—

—

3

Receive Tip

Transmit Tip

4

Receive Ring

Transmit
Ring

5

—

—

6

—

—

7

—

—

8

Patch Panel Cabling for Redundancy

You can connect the patch panels with the interface modules for redundancy, using the Y-cables. The Y-cable
stub lengths are reduced, so that the cable does not exceed from the rack spacer. The Y-cables are numbered
based on the different stub length. Cable lengths differ for even numbered and odd numbered slots in the
chassis.

Do not try to interchange the cables as the length may vary based on odd and even slots.

Note

Cisco ASR 907 Router Hardware Installation Guide

110

Installing the Cisco ASR 907 Router

Patch Panel Pinout

«
...
118
119
120
121
122
...
»

Summary of Contents for ASR 907













































































































































































































Reviews:

No comments

Related manuals for ASR 907

Brand: Linksys Pages: 2

Network Card-MS

Brand: Eaton Pages: 89

Brand: Garland Pages: 4

APS6-400 Series

Brand: Eaton Pages: 114

Brand: Idis Pages: 31

Brand: MiWire Pages: 24

Brand: Variscite Pages: 17

RuggedSwitch RS500

Brand: RuggedCom Pages: 16

Brand: IEI Technology Pages: 106

ServCon FPS-3003

Brand: LevelOne Pages: 45

Brand: netsys Pages: 243

Internet Security Appliances

Brand: SonicWALL Pages: 293

iConverter GX/F

Brand: Omnitron Systems Technology Pages: 2

Brand: D-Link Pages: 37

Brand: Dell Pages: 90

Brand: Cisco Pages: 60

Linksys BEFVP41 v2

Brand: Cisco Pages: 83

Catalyst 2900 Series XL

Brand: Cisco Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands