Cisco ASR 907 Hardware Installation Manual Download Page 163 | Manualshive

Page: 163 / 204

background image

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive

San Jose, California 95134-1706

.
.
.

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: yes

Press RETURN to get started!

Step 2

The first sections of the configuration script appear only at an initial system startup. On subsequent uses of
the setup facility, the script begins with a System Configuration Dialog as shown below: When asked if you
would like to enter the initial configuration dialog, enter yes.

Example:

Would you like to enter the initial configuration dialog? [yes/no] yes
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Basic management setup configures only enough connectivity for management of the system,
extended setup will ask you to configure each interface on the system.

Basic management setup configures enough connectivity for managing the system; extended setup will ask
you to configure each interface on the system. For detailed information about setting global parameters, refer
to the Cisco ASR 907 Router

Software Configuration Guide.

Checking the Running Configuration Settings

To check the value of the settings you have entered, enter the show running-config command at the Router#
prompt:

Router# show running-config

To review changes you make to the configuration, use the EXEC mode

show startup-config

command to

see the changes and copy run-start stored in NVRAM.

The ROMMON variable is set from factory to boot the IOS as ?"BOOT="bootflash:Image/packages.conf"?.
However, the boot command is not pre-configured.

As the boot command is not configured, the router boots to ROMMON mode after the first power cycle, and
the following message is displayed:

no valid BOOT image found
Final autoboot attempt from default boot device...
Located tracelogs.030
Image size 6181 inode num 13, bks cnt 2 blk size 8*512
Boot image size = 6181 (0x1825) bytes
Unknown image structure
boot: cannot determine first file name on device "bootflash:/"
rommon1>.

Cisco ASR 907 Router Hardware Installation Guide

153

Cisco Router Initial Configuration

Checking the Running Configuration Settings

«
...
161
162
163
164
165
...
»

Summary of Contents for ASR 907













































































































































































































Reviews:

No comments

Related manuals for ASR 907

Enterprise Filter Authentication R3000

Brand: 8e6 Technologies Pages: 66

Brand: Aastra Pages: 2

Brand: Draytek Pages: 8

Brand: Lorex Pages: 186

Brand: LogLogic Pages: 30

Brand: Mercusys Pages: 35

Hollywood DV-Bridge

Brand: Dazzle Pages: 63

Brand: Eaton Pages: 14

Brand: ADTRAN Pages: 2

Brand: Moxa Technologies Pages: 51

Brand: ZKTeco Pages: 68

Brand: StarTech.com Pages: 9

Brand: LevelOne Pages: 3

NetVanta Analog Modem Dial Backup Interface Module

Brand: ADTRAN Pages: 2

NVR2104/2108HS-W-4KS2 1U

Brand: Dahua Technology Pages: 363

MP5S Plus Writer

Brand: SONIX Pages: 23

CNGE28FX4TX24MS2

Brand: Comnet Pages: 154

Brand: Belkin Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands