Cisco ASR 907 Hardware Installation Manual Download Page 72

Page: 72 / 204

Step 4

Position cable guides on the router chassis.

Step 5

Ensure to select the 21-inches or 23-inches adapter for your plenum based on your rack size.

The 19-inches bracket is an integral part of the plenum base.

Note

Figure 35: Different Adapters

Figure 36: Plenum Installation on Various Racks

Step 6

Position the plenum assembly to the rack and secure the cable brackets to the rack using a torque of 11.5 in.-lb
(1.3 N-m). See figure below.

For a 19-inch rack installation, the rack has to have a flat post.

Note

Cisco ASR 907 Router Hardware Installation Guide

Installing the Cisco ASR 907 Router

Installing Plenum A907-F2B-AIR-U Assembly and Chassis in the Rack

Summary of Contents for ASR 907












































































































































































































Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands

Cisco ASR 907, Hardware Installation Manual

Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands