Cisco ASR 907 Hardware Installation Manual Download Page 102 | Manualshive

Page: 102 / 204

background image

The Cisco ASR 907 Router power supplies are hot-swappable. If you have installed redundant power supply
modules, you can replace a single power supply without interrupting power to the router.

Note

To avoid erroneous failure messages, allow at least 2 minutes for the system to reinitialize after a power supply
has been removed or replaced.

Caution

When you install the unit, the ground connection must always be made first and disconnected last. Statement
1046

Warning

Before performing any of the following procedures, ensure that power is removed from the AC circuit.
Statement 1003

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement
1030

Warning

Installation of the equipment must comply with local and national electrical codes. Statement 1074

Warning

Follow these steps to remove and replace the AC power supply:

Procedure

Step 1

Disconnect the power cord from the power source. Do not touch the metal prongs on the power cord when it
is still connected to the power supply.

Step 2

Remove the power cord from the power connection on the power supply. Do not touch the metal prongs
embedded in the power supply.

Step 3

Loosen the captive installation screws.

Step 4

Grasp the AC power supply with one hand, and slide it part of the way out of the chassis. Place your other
hand underneath the power supply, and slide it completely out of the chassis.

Step 5

If the power supply bay is to remain empty, install a blank filler plate (Cisco part number A900-PWR-BLANK)
over the opening, and secure it with the captive installation screws.

Installing Dust Caps

The following list provides the product IDs (PIDs) for the dust caps that are available for each port type:

Cisco ASR 907 Router Hardware Installation Guide

92

Installing the Cisco ASR 907 Router

Installing Dust Caps

«
...
100
101
102
103
104
...
»

Summary of Contents for ASR 907













































































































































































































Reviews:

No comments

Related manuals for ASR 907

Brand: 3Com Pages: 48

Brand: Cambium Networks Pages: 68

Brand: Cambium Networks Pages: 110

Brand: Eaton Pages: 10

Brand: Lindy Pages: 4

Brand: TP-Link Pages: 3

EdgeLens INT10G8LR56

Brand: Garland Pages: 30

Brand: peplink Pages: 2

Brand: Macsense Pages: 13

Brand: Moxa Technologies Pages: 36

IPS Pro-Module-24C-GE-BP-TM

Brand: Trend Micro Pages: 3

Brand: Accton Technology Pages: 78

LMP-1202G-SFP Series

Brand: ANTAIRA Pages: 19

Brand: Alarm Pages: 5

FiberTwist G6426

Brand: Genexis Pages: 9

XC-16CH-NVR-4TB

Brand: Xyclop Pages: 19

Brand: Patton electronics Pages: 8

Brand: LevelOne Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands