Cisco ASR 907 Hardware Installation Manual Download Page 155 | Manualshive

Page: 155 / 204

background image

Connector

Male/Female

Length

Product Number

Cable Type

DB-15

Female

10 ft.

CAB-SS-X21FC

X.21 DCE

DB-25

Male

10 ft.

CAB-SS-530MT

EIA/TIA-530 DTE

DB-25

Female

10 ft.

CAB-SS-530FC

EIA/TIA-530 DTE

Table 13: Interface Cables for 68-Pin Connector

Connector

Male/Female

Length

Product Number

Cable Type

DB-25

Male

10 ft.

CAB-HD4-232MT

4-port EIA-232 DTE

DB-25

Female

10 ft.

CAB-HD4-232FC

4-port EIA-232 DCE

RJ-45

Female

10 ft.

CAB-QUAD-ASYNC-F

4-port EIA-232 DTE

RJ-45

Male

10 ft.

CAB-QUAD-ASYNC-M

4-port EIA-232 DTE

DB-9

Male

10 ft.

CAB-9AS-M

4-port EIA-232 DTE

For more information on cable specifications and pinouts, see Troubleshooting.

Connecting the Fan Tray Alarm Port

The fan tray includes an alarm port that maps to 4 dry contact alarm inputs.

The pins on the alarm port are passive signals and can be configured as Normally Open (an alarm generated
when current is interrupted) or Normally Closed (an alarm is generated when a circuit is established) alarms.
You can configure each alarm input as critical, major, or minor. An alarm triggers alarm LEDs and alarm
messages. The relay contacts can be controlled through any appropriate third-party relay controller. The
open/close configuration is an option controlled in IOS.

To comply with the Telcordia GR-1089 NEBS standard for electromagnetic compatibility and safety, connect
the alarm ports only to intra-building or unexposed wiring or cable. The intrabuilding cable must be shielded
and the shield must be grounded at both ends. The intra-building port(s) of the equipment or subassembly
must not be metallically connected to interfaces that connect to the OSP or its wiring. These interfaces are
designed for use as intra-building interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE)
and require isolation from the exposed OSP cabling. The addition of Primary Protectors is not sufficient
protection in order to connect these interfaces metallically to OSP wiring.

Warning

Only Pins 1, 2, 4, 6, and 8 are available for customer use. The remaining pins are for Cisco manufacturing
test, and should not be connected. Use a shielded cable for connection to this port for EMC protection. To
understand the pinouts on the alarm port in Troubleshooting.

Procedure

Step 1

Attach an RJ45 cable to the alarm port.

Cisco ASR 907 Router Hardware Installation Guide

145

Installing the Cisco ASR 907 Router

Connecting the Fan Tray Alarm Port

«
...
153
154
155
156
157
...
»

Summary of Contents for ASR 907













































































































































































































Reviews:

No comments

Related manuals for ASR 907

Brand: National Instruments Pages: 26

Brand: National Instruments Pages: 85

Module SCXI-1503

Brand: National Instruments Pages: 79

Brand: CSS Pages: 2

Brand: Oracle Pages: 24

Brand: IEI Technology Pages: 86

Lite N42B1P Series

Brand: Dahua Technology Pages: 14

Brand: Kanguru Pages: 13

Brand: Xenya Pages: 189

Brand: B+B SmartWorx Pages: 52

Brand: NC-link Pages: 20

Brand: Gemtek Systems Pages: 51

Brand: RubyTech Pages: 25

Brand: Unex Pages: 27

Brand: TP-Link Pages: 2

Brand: Transition Networks Pages: 5

Brand: Xaptum Pages: 24

Threat Analysis Reporter TAR HL/SL/MSA

Brand: 8e6 Technologies Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands