Cisco ASR 907 Hardware Installation Manual Download Page 149

Page: 149 / 204

Figure 92: Wall Mount - Dual

Step 2

Secure the bracket to the device with the recommended maximum torque of 10 inch-pounds (1.1 newton
meters).

Step 3

Position the device vertically on the wall.

Before mounting the device, ensure that all unused holes at the sides of the device are protected
with screws.

Caution

Step 4

Use a tape measure and level to verify that the device is installed straight and on level.

Patch Panel Dimensions

Following are the various patch panel dimensions.

Cisco ASR 907 Router Hardware Installation Guide

139

Installing the Cisco ASR 907 Router

Patch Panel Dimensions

Summary of Contents for ASR 907












































































































































































































Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands

Cisco ASR 907, Hardware Installation Manual

Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands